Toyota PAB4-Toyota RAV4
1. Operation of the car
2. Maintenance
3. Engines
4. Cooling systems and conditioning
5. Fuel system and system of production of the fulfilled gases
6. System of ignition
7. The control system and decrease in toxicity of the fulfilled gases
8. Coupling
9. Transmission
10. Driveshaft and shaft of the drive of driving wheels
11. Brake system
12. Suspension bracket
13. Steering and running gear
14. Body
   General information
   Care of a body
   Care of an upholstery and rugs
   Repair of insignificant damages of a body
   Repair of considerable damages of a body
   Service of hinges and locks
   Recommendations about replacement of a windshield and motionless glasses
   Removal and installation of a cowl
   Lock and cable of opening of the lock of a cowl
   Removal and installation of bumpers
   Removal and installation of forward wings
   Removal and installation of facing of the Radiator
   Removal and installation of the deflector of a ventilating grate
   Removal and installation of an upholstery of doors
   Doors
   Removal and installation of glasses of doors
   Removal and installation of window regulators
   Removal and installation of an external rear-view mirror
   Removal and installation of an internal rear-view mirror
   Door of the luggage compartment
   Removal and installation of the central console
   Removal and installation of elements of finishing of the dashboard
   Removal and installation of casings of a steering column
   Removal and installation of the dashboard
   Removal and installation of seats
   Adjustment of the lifting and movable panel of a roof
15. Electric equipment
Schemes of electric equipment


Toyota RAV4>> Body>> Lock and cable of opening of the lock of a cowl
       PREVENTION
Cars are equipped with security systems (SRS) including safety cushions and natyazhitel of seat belts. Before work about sensors of blow, the dashboard and a steering column disconnect at first negative, and then positive plugs from the rechargeable battery and wait 2 min. It will exclude unauthorized disclosure of safety cushions and operation of natyazhitel of seat belts which can put injuries.

You make removal of the lock of a cowl as follows:

Fig. 14.2. Arrangement of bolts of fastening of the lock of a cowl


Marker note the provision of bolts of fastening of the lock of a cowl (see fig. 14.2 ). Turn out bolts and remove the lock from the forward cross panel.

Fig. 14.3. A cable cover detachment from the cowl lock case


Disconnect a cable cover from the case of the lock of a cowl and a cable from a latch of the lock (fig. 14.3) .
You make installation in the sequence, the return to removal, taking into account the following: adjust position of the lock so that gaps between a forward part of a cowl and wings were identical, and a rubber emphasis when closing a cowl slightly contracted.
You make removal of a cable of opening of the lock of a cowl as follows:
In interior of the car remove the upholstery panel located under the dashboard from the driver.

Fig. 14.4. A cable detachment from the handle of opening of a cowl: And — the place of fastening of a cover of a cable; In — the place of fastening of a cable to the squeezing lever; With — a clamp


Lift the handle of opening of a cowl up and disconnect a cable cover from a handle arm, then disconnect a cable from the squeezing lever (fig. 14.4) .
If squeezing the lever with the handle are replaced, pull the handle outside and press for removal from a clamp and its detachment from the dashboard down.
Tie a thin long cord to a cable. Further the cord will be required for retraction to the place of a cable of opening of a cowl.
In a motor compartment disconnect a cable and a cover of a cable from the cowl lock. Release a cable from clips on a forward cross beam and along a wing.
Extend a cable in a motor compartment, before emergence of a cord, then untie a cord from an old cable and fix it on a new cable.
For a cord stretch a new cable through a partition of a motor compartment until it reaches the handle of opening of a cowl, then untie a cord.
In interior of the car connect a cable to the squeezing lever, and fix a cover of a cable on a handle arm.
If at installation of a cable the condensing ring was displaced from a partition of a motor compartment, establish by fingers of a hand it into place.
You make further installation in the sequence, the return to removal.