Toyota PAB4-Toyota RAV4
1. Operation of the car
2. Maintenance
3. Engines
4. Cooling systems and conditioning
5. Fuel system and system of production of the fulfilled gases
6. System of ignition
7. The control system and decrease in toxicity of the fulfilled gases
8. Coupling
9. Transmission
10. Driveshaft and shaft of the drive of driving wheels
11. Brake system
12. Suspension bracket
13. Steering and running gear
14. Body
   General information
   Care of a body
   Care of an upholstery and rugs
   Repair of insignificant damages of a body
      Processing of scratches of a body
      Repair of dents of a surface of a body
      Hard putty and painting of a body
   Repair of considerable damages of a body
   Service of hinges and locks
   Recommendations about replacement of a windshield and motionless glasses
   Removal and installation of a cowl
   Lock and cable of opening of the lock of a cowl
   Removal and installation of bumpers
   Removal and installation of forward wings
   Removal and installation of facing of the Radiator
   Removal and installation of the deflector of a ventilating grate
   Removal and installation of an upholstery of doors
   Removal and installation of glasses of doors
   Removal and installation of window regulators
   Removal and installation of an external rear-view mirror
   Removal and installation of an internal rear-view mirror
   Door of the luggage compartment
   Removal and installation of the central console
   Removal and installation of elements of finishing of the dashboard
   Removal and installation of casings of a steering column
   Removal and installation of the dashboard
   Removal and installation of seats
   Adjustment of the lifting and movable panel of a roof
15. Electric equipment
Schemes of electric equipment

Toyota RAV4>> Body>> Repair of insignificant damages of a body>> Hard putty and painting of a body
When performing spackling works it is necessary to have the wide flexible plastic or nylon pallet for giving of smoothness of a surface of hard putty. When working on a shpaklevaniye of a body adhere to the following recommendations:
Level hard putty on the damaged site of a body so that to give it the required form and smoothness.
As soon as it was succeeded to achieve approximately required contour, stop smoothing down hard putty the pallet as at too long smoothing down it will begin to harden, stick on the pallet and to roll down therefore the surface will be damaged.
You apply the subsequent, more thin film of hard putty, only after drying of the previous layer and so until the level of hard putty does not begin to act slightly over the processed site.
After hard putty hardening remove its surplus with a metal scraper or a file.
You make further processing, using at the first stage a coarse-grained emery paper, then fine-grained. An emery paper have on flat wooden whetstone, otherwise it will be impossible to achieve a plain surface.
On a closing stage of grinding the waterproof emery paper should be moistened with water periodically. It will give to the processed puttied surface special smoothness.
The puttied dent has to be surrounded on perimeter with a layer of pure metal. For removal of dust and fats wash out the processed site water and wipe with the degreasing means.
Raise dust on the site a thin layer of light soil. It will help to reveal all defects allowed when processing in hard putty. Level them by means of a new layer of hard putty and again to a zashkurta a surface.
After that the field of repair is ready to final painting.
Aerosol putting paint has to be carried out in the warm, dry, windless and easy atmosphere.
When carrying out painting indoors moisten half of the working platform with water for prevention of hit in dust air. When coloring only of one panel, other parts of a body have to be covered from hit of paint on them with the newspaper attached by an adhesive tape.
Before putting primer carefully mix it, apply on a trial surface and achieve that she laid down evenly. Put a thick layer of primer for what apply several thin films.
Polish the grounded surface a waterproof emery paper. At the same time do not forget to sprinkle the ground area water and to periodically moisten an emery paper in water.
Before further painting dry up the processed site.
Put a paint coat with a spray. Necessary thickness of a paint coat is reached by drawing several thin layers.
Begin coloring from the center of the processed surface and move to edges back and forth motions until all painted surface and area at distance about 20 mm around it are not painted.
Remove a protective film and newspapers later 10–15 minposl of drawing the last paint coat.
Give the chance to fresh paint to harden within at least two weeks, then by means of an obnovitel of paint or thin abrasive polishing paste even the edges of the painted area to the level of old paint.
Polish a surface.