Device and repair of Toyota RAV4 SUVs (Toyota RAV) - Removal and installation of the pump of the amplifier of steering-//

Toyota PAB4-Toyota RAV4
1. Operation of the car
2. Maintenance
3. Engines
4. Cooling systems and conditioning
5. Fuel system and system of production of the fulfilled gases
6. System of ignition
7. The control system and decrease in toxicity of the fulfilled gases
8. Coupling
9. Transmission
10. Driveshaft and shaft of the drive of driving wheels
11. Brake system
12. Suspension bracket
13. Steering and running gear
   General information
   Technical characteristics
   Removal and installation of a steering wheel with a safety cushion
   Removal and installation of a steering column
   Removal and installation of tips of steering drafts
   Replacement of covers of the steering mechanism
   Removal and installation of the steering mechanism
   Removal and installation of the pump of the amplifier of steering
   Pumping of hydraulic system of the amplifier of steering
   Replacement of bolts of fastening of a wheel
   Wheels and tires
14. Body
15. Electric equipment
Schemes of electric equipment


Toyota RAV4>> Steering and running gear>> Removal and installation of the pump of the amplifier of steering
Till 2001 you make removal of the pump of the amplifier of steering for models as follows.
Switch off ignition and disconnect a wire of "weight" from the rechargeable battery.
The syringe pump out liquid from a tank of the amplifier of steering.
Install under a motor compartment the reception pallet for collecting liquid.
Tighten the parking brake and block back wheels an emphasis.
Lift the car on the elevator, remove protection of a motor compartment.
Remove forward section of system of production of the fulfilled gases.

Fig. 13.15. An arrangement of the left bolts of fastening of a cross beam on models till 2001


Remove tips of steering drafts from rotary fists and turn out a bolt of fastening of the steering mechanism to a cross beam, then turn out bolts and remove a cross beam of a forward suspension bracket (see fig. 13.15 ).

Fig. 13.17. Arrangement of hinged and tightening bolts of fastening of the pump of the amplifier of steering


Weaken hinged and tightening bolts, move the pump of the amplifier of steering to the engine and take off a pump drive belt ( fig. 13.17 ).
Weaken a collar and disconnect a hose of return of liquid from the pump;

Fig. 13.18. A reversing of the union of a delivery hose (1) from the pump of the amplifier of steering


cap key turn out the union of a delivery hose from the pump ( fig. 13.18 ).
Disconnect two vacuum hoses from the pump.

Fig. 13.19. An arrangement of bolts of fastening of an arm of the pump of the amplifier of steering on models till 2001


Turn out bolts of fastening of an arm of the pump and remove the pump ( fig. 13.19 );
if necessary turn out nuts and remove the pump from an arm.
You carry out installation of the pump to the sequences, the return to removal, taking into account the following.
Adjust pump drive belt tension.
Add liquid in a tank of the amplifier of steering and remove air from hydraulic system.
Since 2001 you make removal of the pump of the amplifier of steering for models as follows:
Switch off ignition and disconnect a wire of "weight" from the rechargeable battery.
The syringe pump out liquid from a tank of the amplifier of steering.
Install under a motor compartment the reception pallet for collecting liquid.
Take off a belt of the drive of the pump of the amplifier of steering.
Tighten the parking brake and block back wheels an emphasis.
Weaken nuts of fastening of the right forward wheel.
Lift a forward part of the car and establish on support.
Remove the right forward wheel and an antisplash guard of an arch of the right forward wheel.
Disconnect the electric socket from the sensor of pressure of the amplifier of steering.
Turn out a hollow bolt and disconnect a delivery hose from the pump.
Weaken a collar and disconnect a hose of return of liquid from the pump.

Fig. 13.20. An arrangement top (In) and lower (And) bolts of fastening of the pump of the amplifier of steering on models since 2001


Turn out the lower bolt, then weaken the top bolt and remove the pump of the amplifier of steering from the engine ( fig. 13.20 ).
You carry out installation of the pump to the sequences, the return to removal, taking into account the following:
At installation of a hollow bolt of fastening of a delivery hose use new sealing laying.
Establish a wheel, screw nuts, lower the car and tighten nuts of fastening of a wheel.
Establish a belt of the drive of the pump and adjust its tension.
Add liquid in a popolnitelny tank of the amplifier of steering and remove air from hydraulic system.