Toyota PAB4-Toyota RAV4
1. Operation of the car
2. Maintenance
3. Engines
4. Cooling systems and conditioning
5. Fuel system and system of production of the fulfilled gases
6. System of ignition
7. The control system and decrease in toxicity of the fulfilled gases
8. Coupling
9. Transmission
10. Driveshaft and shaft of the drive of driving wheels
11. Brake system
   General information
   Specifications
   Anti-blocking system of brakes (ABS)
      Elements of anti-blocking system of brakes
      Removal and installation of elements of anti-blocking system of brakes
   Replacement of front brake shoes
   Replacement of a support of a forward brake
   Check and replacement of brake disks
   Replacement of back brake shoes
   Replacement of the working brake cylinder
   Replacement of the main brake cylinder
   Replacement of sealing rings of a tank of the brake system
   Replacement of brake tubes and hoses
   Pumping of the hydraulic drive of brakes
   Check and replacement of the vacuum amplifier of brakes
   Adjustment of the parking brake
   Replacement of cables of the parking brake
   Adjustment of provision of a pedal of a brake
   Check and replacement of the switch of a stoplight
12. Suspension bracket
13. Steering and running gear
14. Body
15. Electric equipment
Schemes of electric equipment


Toyota RAV4>> Brake system>> Anti-blocking system of brakes (ABS)>> Removal and installation of elements of anti-blocking system of brakes
ABS modulator

Fig. 11.10. The ABS modulator of models till 2001 (the modulator of models 4WD of 1996 has insignificant differences): 1 – bolt; 2, 4 – a pillow; 3 – ABS modulator; 5 – modulator arm; 6 – tank of the amplifier of steering


Fig. 11.11. The ABS modulator of models since 2001: 1 – bolt; 2 – electric socket of the modulator; 3 – bolt; 4, 9 – pillows; 5 – a tank of the amplifier of steering with an arm; 6 – ABS modulator; 7 – pillow; 8 – modulator arm


Enclose under the modulator pure rags for collecting the leaked brake fluid. A cap key turn off nuts and disconnect 6 tubes from the ABS modulator (fig. 11.10 , 11.11 ).
Remove and take aside a compensation tank of the amplifier of steering. On models till 2001 turn out a bolt and disconnect the holder of a pipe of the amplifier of steering from an ABS modulator arm.
Disconnect the electric socket from the ABS modulator.
Turn out bolts and remove the ABS modulator together with an arm.
If necessary turn out bolts and remove the ABS modulator from an arm.
You make installation in the sequence, the return to removal.
After installation remove air from the hydraulic brake system.
Sensor of frequency of rotation of a forward wheel
Tighten the parking brake and block back wheels an emphasis.
Weaken nuts of fastening of a forward wheel. Lift a forward part of the car and establish it on support. Remove a forward wheel and an antisplash guard of an arch of a forward wheel.
Track an arrangement of the electric socket on a sensor wire and disconnect the socket.
Turn out bolts of fastening of a wire of the sensor.

Fig. 11.3. Forward sensor of frequency of rotation: 1 – rotor of the sensor of frequency of rotation of a forward wheel; 2 – plug; 3 – sensor of frequency of rotation of a forward wheel


Turn out a bolt and remove the sensor of frequency of rotation of a wheel and the plug from a rotary fist (see fig. 11.3 ).
You make installation in the sequence, the return to removal, taking into account the following.
Bolt of fastening of the sensor tighten the moment of 8 N • m.
The sensor of frequency of rotation of a back wheel on all models, except models with one leading bridge of release since 2001
Remove a pillow and a back of a back seat.
Disconnect the electric socket, then push out the condensing ring and a wire of the sensor from a trough-shaped element of a floor.
Block forward wheels an emphasis. Weaken nuts of fastening of a back wheel. Lift a back part of the car and establish it on support.
Turn out a bolt of fastening of a cable of the parking brake to the lever of a back suspension bracket.
Turn out a bolt of fastening of a plait of wires to a protective arm.

Fig. 11.4. The back sensor of frequency of rotation on all models till 2001 and on all-wheel drive models since 2001: 1 – sensor of frequency of rotation of a back wheel; 2 – rotor of the sensor of frequency of rotation of a back wheel


Turn out a bolt and remove the sensor of frequency of rotation of a wheel and the plug from a back beam (fig. 11.4) .
You make installation in the sequence, the return to removal, taking into account the following.
Bolt of fastening of the sensor tighten the moment of 8 N • m.
The sensor of frequency of rotation of a back wheel on models with one leading bridge of release since 2001
Block forward wheels an emphasis. Weaken nuts of fastening of a back wheel. Lift a back part of the car and establish it on support.

Fig. 11.5. The back sensor of frequency of rotation on models with one leading bridge of release since 2001: 1 – electric socket; 2 – sensor of frequency of rotation of a back wheel; 3 – nave; 4 – brake drum


Disconnect the electric socket from the sensor of frequency of rotation of a back wheel (fig. 11.5) .
Remove a nave of a back wheel together with the bearing.
The hammer through a tubular mandrel beat out the sensor from a support of a back nave.
You make installation in the sequence, the return to removal, taking into account the following.
The press and the adapter installed on an external ledge of the sensor is necessary for installation of the new sensor.
Delay sensor
Remove a back part of the central console.

Fig. 11.12. Delay sensor: 1 – electric socket; 2 – delay sensor


Disconnect the electric socket from the sensor, turn out 2 nuts and remove the delay sensor (fig. 11.12 ).
You make installation in the sequence, the return to removal.