Toyota PAB4-Toyota RAV4
1. Operation of the car
2. Maintenance
3. Engines
4. Cooling systems and conditioning
5. Fuel system and system of production of the fulfilled gases
6. System of ignition
7. The control system and decrease in toxicity of the fulfilled gases
8. Coupling
9. Transmission
   General information
   Specifications
   Repair of the transmission
   The repair and adjusting work performed on cars with the mechanical transmission
   The repair and adjusting work performed on cars with the automatic transmission
      Diagnostics of the automatic transmission
      Replacement of sealing cuffs
      Check, adjustment and replacement of a cable of management of a butterfly valve
      Replacement and adjustment of a cable of the selector
      Replacement and adjustment of the switch of blocking of a starter (PNP)
      Check of system of blocking of the lever of the selector and lock of ignition
      Removal and installation of the automatic transmission on models with one leading bridge
      Removal and installation of the automatic transmission on all-wheel drive models
10. Driveshaft and shaft of the drive of driving wheels
11. Brake system
12. Suspension bracket
13. Steering and running gear
14. Body
15. Electric equipment
Schemes of electric equipment


Toyota RAV4>> Transmission>> The repair and adjusting work performed on cars with the automatic transmission>> Removal and installation of the automatic transmission on models with one leading bridge
Removal
Switch off ignition and disconnect a wire of "weight" from the rechargeable battery.
Remove a cowl.
Remove a broad tank.
On release models till 2001 weaken a lock-nut and remove a cable cover from an arm of throttle knot. Disconnect a cable from the sector of a butterfly valve.
Remove a starter.
Mark and disconnect all electric sockets from the transmission.
Turn off a bolt of fastening of a wire of "weight".
Turn out bolts of fastening of the transmission available from above to the engine.
Establish a cross-piece over a motor compartment and fix by a chain for an eye the transmission to a cross-piece.
Turn out a bolt of fastening of the left support of the transmission.
Weaken nuts of fastening of power shafts to naves of forward wheels.
Tighten the parking brake and block back wheels. Lift a forward part of the car and establish it on support. Remove forward wheels.
Remove a mudguard of a motor compartment.
Turn off a nut of fastening of a cable of the selector and disconnect it from the lever of the choice of transfers on the forward party of the transmission.
Remove a clip and remove a cable cover from an arm on the transmission.
Merge transmission liquid from the transmission.
Remove power shafts.
Remove a reception exhaust pipe.
Mark and disconnect all electric sockets available from below from the transmission.
Disconnect the hoses going to the oil heater from the transmission. Close the ends of hoses plastic traffic jams.
Turn out a bolt of fastening of the steering mechanism to the lower cross beam. Fix by a soft wire steering transfer on the beam established across a motor compartment.
On models since 2001 remove a cap, closing an opening for access to the hydrotransformer, then paint note position of the hydrotransformer and a plate of the drive.
On models 1996 and 1997 of years disconnect a selector cable from the lower cross beam.
On models since 2001 disconnect earrings of the stabilizer of cross stability from the stabilizer.
Remove the lower cross and longitudinal beams.

Fig. 9.29. Arrangement of bolts of fastening of a plate of rigidity


On models till 2001 turn out bolts and remove a plate of rigidity (fig. 9.29) .
On models till 2001 paint note position of the hydrotransformer and a plate of the drive.
Turn out bolts of fastening of the hydrotransformer. For access to each subsequent bolt turn a bent shaft of the engine in the direction of its working rotation for the central bolt of fastening of a pulley of a bent shaft.
Support the transmission by a transmission jack.
Turn out the remained bolts of fastening of the transmission to the engine, at the same time note an arrangement of bolts as they have various length.
Take away the transmission from the engine and check that the hydrotransformer is separated from a drive plate. Fix by captures the hydrotransformer, lower and remove the transmission.
Installation
You make installation in the sequence, the return to removal taking into account the following.
Combine the tags on the hydrotransformer and a plate of the drive put before removal.
Fill in transmission liquid in the transmission.
Adjust a selector cable, and a cable of management of a butterfly valve (on models till 2001).