Device and repair of Toyota RAV4 SUVs (Toyota RAV) - The fuel pump-//

Toyota PAB4-Toyota RAV4
1. Operation of the car
2. Maintenance
3. Engines
4. Cooling systems and conditioning
5. Fuel system and system of production of the fulfilled gases
   General information
   Technical characteristics of system of injection of fuel
   Dropping pressure in fuel system
   General check of fuel system
   Fuel pump
   Fuel pressure regulator
   Fuel level sensor
   Fuel tank
   Case of the air filter
   Accelerator cable
   Electronic system of injection of fuel
   Damper of pulsations of fuel on models since 2001
   Distributive fuel highway and nozzles
   System of production of the fulfilled gases
6. System of ignition
7. The control system and decrease in toxicity of the fulfilled gases
8. Coupling
9. Transmission
10. Driveshaft and shaft of the drive of driving wheels
11. Brake system
12. Suspension bracket
13. Steering and running gear
14. Body
15. Electric equipment
Schemes of electric equipment


Toyota RAV4>> Fuel system and system of production of the fulfilled gases>> Fuel pump
You make removal of the fuel pump as follows.
Dump pressure in fuel system.
Remove a stopper from a jellied mouth of the fuel tank.
Switch off ignition and disconnect a wire of "weight" from the rechargeable battery.

Fig. 5.6. The fuel pump on cars till 2001 of release: 1 – laying; 2 – block of the fuel pump / fuel level sensor; 3 – fuel return hose; 4 – laying; 5 – electric socket of the fuel pump / fuel level sensor; 6 – the cover closing an opening for service of the fuel pump / fuel level sensor; 7 – laying; 8 – fuel supply tube; 9 – fuel filter; 10 – fuel supply hose; 11 – sealing ring; 12 – fuel pressure regulator; 13 – clip


Fig. 5.7. The fuel pump on cars since 2001 of release: 1 – laying; 2 – block of the fuel pump / fuel level sensor; 3 – electric socket of the sensor of pressure of vapors of fuel; 4 – cover of the fuel tank; 5 – electric socket of the fuel pump / fuel level sensor; 6 – the cover closing an opening for service of the fuel pump / fuel level sensor; 7 – main tube of the fuel tank; 8 – clamp; 9 – fuel absorption plate; 10 – belt of fastening of the fuel pump; 11 – block of the fuel filter; 12 – cover; 13 – tube; 14 – fuel pump; 15 – clip; 16 – rubber pillow; 17 – support; 18 – auxiliary hose of absorption of fuel


For access to the block of the fuel pump / sensor of level remove a back seat and the cover closing an opening for service of the fuel pump / fuel level sensor (fig. 5.6, 5.7) .
Disconnect the electric socket from the block of the fuel pump / fuel level sensor. Disconnect fuel hoses and, in the presence, the electric socket of the sensor of pressure of vapors of fuel.
Turn out bolts of fastening of a cover of the block of the fuel pump / fuel level sensor.

Fig. 5.8. The place of fastening of an auxiliary hose of absorption of fuel to the block of the fuel pump / fuel level sensor on models since 2001 of release


Being careful, take the block of the fuel pump / fuel level sensor from the fuel tank. On models since 2001 of release after the block of the fuel pump / fuel level sensor leaves the fuel tank, from the lower party of the block disconnect an auxiliary hose of absorption of fuel (fig. 5.8) .
Disconnect the electric socket from the fuel pump.
Remove the fuel pump from the block.

Fig. 5.9. Removal of the lower part of the fuel pump from an arm on models till 2001 of release


On models till 2001 weaken a collar and remove a hose, then take the lower part of the pump from an arm (fig. 5.9) .
On models since 2001 disconnect the fuel level sensor , moving the pump from a fuel absorption plate.
Remove the fuel filter and a plate of absorption from clamps.
Disconnect the electric socket from the fuel pump.

Fig. 5.10. An arrangement of clamps of fastening of a fuel tube to the fuel pump on models till 2001 of release


Fig. 5.11. A detachment of a belt of fastening of the fuel pump and separation of the pump from the block on models since 2001 of release


Pick up the top arm and the fuel phone from clamps of the pump (fig. 5.10) , disconnect a belt of fastening of the fuel pump (fig. 5.11) and separate the pump from the block.
Edge of the thin screw-driver remove a zabornik of fuel and a rubber pillow from the lower part of the fuel filter.

Fig. 5.12. An arrangement of a spring clip of fastening of the mesh filter to the fuel pump


Remove a spring clip and remove the mesh filter (fig. 5.12) from the fuel pump .
You carry out installation of the fuel pump as it should be, the return to removal.