Toyota PAB4-Toyota RAV4
1. Operation of the car
2. Maintenance
3. Engines
   Repair of the engine 3S-FE without its removal from the car
      General information
      Specifications
      Installation of the piston of the first cylinder in the top dead point (TDP)
      Cover of a head of the block of cylinders
      Inlet collector
      Final collector
      Gear belt and pulleys of a gear belt
      Forward sealing ring of a bent shaft
      Sealing ring of the camshaft
      Camshafts and pushers of valves
      Head of the block of cylinders
      Oil pallet
      Oil pump
      Drive flywheel / plate
      Back sealing ring of a bent shaft
      Support of the power unit
   Repair of the engine 1AZ-FE without its removal from the car
   Diagnostics and preparation of the engine for capital repairs
4. Cooling systems and conditioning
5. Fuel system and system of production of the fulfilled gases
6. System of ignition
7. The control system and decrease in toxicity of the fulfilled gases
8. Coupling
9. Transmission
10. Driveshaft and shaft of the drive of driving wheels
11. Brake system
12. Suspension bracket
13. Steering and running gear
14. Body
15. Electric equipment
Schemes of electric equipment


Toyota RAV4>> Engines>> Repair of the engine 3S-FE without its removal from the car>> Support of the power unit
Support of the power unit usually do not require attention, however the broken or damaged support demand immediate replacement as car transmission elements can be damaged.
Check
When checking raise a little the power unit that support were in not loaded state.
Lift the car on the elevator and remove an antisplash guard of a motor compartment. A jack through the wooden whetstone established under the oil pallet lift the power unit so that the weight of the power unit was perceived by a jack.
Check support of the power unit for lack of stratifications of rubber and its separation from the central metal plugs.
Mount check lack of movement of support of the power unit.
Replacement
You make replacement in the following order:
– switch off ignition and disconnect a wire of "weight" from the rechargeable battery;
– lift the car on the elevator and remove an antisplash guard of a motor compartment. A jack through the wooden whetstone established under the oil pallet lift the power unit so that its weight was perceived by a jack;
Right side support of the engine

Fig. 3.48. Arrangement of the lower nut of fastening of the right side support of the engine


– from below the car turn out a nut of fastening of a support to the lower cross beam of a motor compartment (fig. 3.48) ;

Fig. 3.49. Arrangement of the top nuts and bolts of fastening of the right side support of the engine


– from above, from a motor compartment, turn out the remained nuts and bolts of fastening of the right side support of the engine (fig. 3.49) and remove it. If the car is equipped with ABS, it is necessary to remove the ABS block previously.
Installation is carried out to the sequences, the return to removal, taking into account the following.
Before a vvorachivaniye of bolts and nuts of fastening of a support, apply the kontrovochny structure interfering their self-unscrewing on their carving.
Forward and back support of the transmission

Fig. 3.50. An arrangement of openings in the lower cross beam of a motor compartment for access to bolts of fastening of a forward support of the transmission and the central bolt of fastening of a support to the transmission


– through openings in the lower cross beam of a motor compartment turn out bolts of fastening of a forward and back support of the transmission (fig. 3.50) ;
– turn out the central bolts of fastening of support to the transmission and remove support.
Installation is carried out to the sequences, the return to removal, taking into account the following.
Before a vvorachivaniye of bolts and nuts of fastening of a support apply the kontrovochny structure interfering their self-unscrewing on their carving.
Left support of the transmission

Fig. 3.51. Arrangement of bolts and nuts of fastening of the left support of the transmission


– turn out bolts and nuts of fastening of the left support of the transmission (fig. 3.51) and remove a support.
– turn out the central bolt of fastening of a support to the transmission and remove a support.
You carry out installation to the sequences, the return to removal, taking into account the following: before a vvorachivaniye of bolts and nuts of fastening of a support apply the kontrovochny structure interfering their self-unscrewing on their carving.