Toyota PAB4-Toyota RAV4
1. Operation of the car
2. Maintenance
3. Engines
   Repair of the engine 3S-FE without its removal from the car
      General information
      Specifications
      Installation of the piston of the first cylinder in the top dead point (TDP)
      Cover of a head of the block of cylinders
      Inlet collector
      Final collector
      Gear belt and pulleys of a gear belt
      Forward sealing ring of a bent shaft
      Sealing ring of the camshaft
      Camshafts and pushers of valves
      Head of the block of cylinders
      Oil pallet
      Oil pump
      Drive flywheel / plate
      Back sealing ring of a bent shaft
      Support of the power unit
   Repair of the engine 1AZ-FE without its removal from the car
   Diagnostics and preparation of the engine for capital repairs
4. Cooling systems and conditioning
5. Fuel system and system of production of the fulfilled gases
6. System of ignition
7. The control system and decrease in toxicity of the fulfilled gases
8. Coupling
9. Transmission
10. Driveshaft and shaft of the drive of driving wheels
11. Brake system
12. Suspension bracket
13. Steering and running gear
14. Body
15. Electric equipment
Schemes of electric equipment


Toyota RAV4>> Engines>> Repair of the engine 3S-FE without its removal from the car>> Oil pallet
Removal
You make removal in the following order:
– switch off ignition and disconnect a wire of "weight" from the rechargeable battery;
– tighten the parking brake and establish an emphasis under back wheels;
– lift a forward part of the car and establish on support;
– remove an antisplash guard of a motor compartment;
– merge engine oil from the engine and turn out an oil filter;
– remove the index (probe) of level of oil;
– turn out 3 nuts of fastening of a reception exhaust pipe to a final collector and 2 bolts of fastening of the catalyst to other part of system of production of the fulfilled gases;
– turn out 2 bolts of fastening of an arm and remove a reception exhaust pipe together with an arm;
– remove a support of a final collector;

Fig. 3.37. Arrangement of bolts of fastening of a forward support of the power unit


– turn out bolts (fig. 3.37) and remove the forward support of the power unit located about a cooling system radiator;
– turn out bolts and remove the oil pallet. If the oil pallet sits strongly, separate it from the block of cylinders, having inserted between them a screw-driver edge, at the same time do not damage the privalochny surfaces of the pallet and block of cylinders.
Installation
Firm plastic or wooden scraper clear the privalochny surfaces of the oil pallet and block of cylinders of the remains of old laying and sealant.
Check that carving openings for bolts of fastening of the oil pallet in the block of cylinders pure and have no damages of a carving.
Check a flange of the oil pallet, especially about openings for bolts, for lack of the deformed sites. If necessary level the privalochny surface of the pallet the hammer on wooden whetstone.
Check fastening of a maslozaborny tube and lack of cracks in it. If the maslozaborny phone was picked up, clear it and establish with a new sealing ring or laying. Check the mesh filter of a maslozabornik for lack of pollution.

Fig. 3.38. Places of drawing a layer of RTV sealant on the privalochny surface of the oil pallet: And — in a groove on a flange; In — around an opening


Apply a layer of RTV sealant with a diameter of 5 mm (fig. 3.38) on the privalochny surface of the oil pallet .
Install the oil pallet on the block of cylinders and fix by bolts, tightening them consistently around in several passes.
Further installation is carried out to the sequences, the return to removal, taking into account the following.
Before filling of engine oil wait 1 h in order that sealant managed to harden.

       NOTE
The oil pallet needs to be installed within 5 min. after putting sealant.

Establish a new oil filter and fill in engine oil in the engine.
At installation of a reception exhaust pipe use new laying.
Launch the engine and check for lack of leaks.